Mindray DPM 1 Instrukcja Operatora Strona 65
- Strona / 120
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
7-3
NOTE
Place the SpO
2
sensor cable along the backside of patient’s hand. Make sure the
fingernail is just opposite to the light emitted from the sensor.
SpO
2
waveform amplitude is not proportional to the pulse strength.
SpO
2
value is not proportional to the pulse rate.
7.3 Monitoring Procedure
1. Power on the monitor.
2. Remove colored nail polish from the application site.
3. Apply the sensor to the patient.
4. Plug the connector of the sensor extension cable into the SpO
2
connector on the
monitor.
7.4 Measurement Limitations
If you doubt the measured SpO2, check patient vital signs first. Then check the patient
monitor and SpO2 sensor. The following factors may influence the accuracy of
measurement:
Ambient light
Physical movement (patient and imposed motion)
Diagnostic testing
Low perfusion
Electromagnetic interference, such as MRI environment
Electrosurgical units
Dysfunctional haemoglobin, such as carboxyhemoglobin (COHb)and methemoglobin
(MetHb)
Presence of certain dyes, such as methylene and indigo carmine
Inappropriate positioning of the SpO2 sensor, or use of incorrect SpO2 sensor
Drop of arterial blood flow to immeaurable level caused by shock, anemia, low
temperature or vasoconstrictor.
The absorption of oxyhemoglobin (HbO
2
) and deoxyhemoglobin to the light of special
wavelength may also affect the accuracy of the SpO
2
measurement. In the presence of other
substances (such as carbon hemoglobin, methemoglobin, methylene blue and indigo
carmine) that absorb the light of the same wavelengths, false or low SpO
2
readings may
result.
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Mindray DPM 1
(274 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji